#Full uninstall 2.11 final serial serial
#Full uninstall 2.11 final serial software
#Full uninstall 2.11 final serial password

#Full uninstall 2.11 final serial password

Set this option to enable VNC access to the container to view the deCONZ ZigBee meshДefault port for VNC mode is 5900 this option can be used to change this portДefault password for VNC mode is 'changeme' this option can (should) be used to change the default password Set the local time zone so deCONZ has the correct time. Set this environment variable to the same string passed to -device to force deCONZ to use the specific USB device.

a Z-Wave stick) deCONZ may not find RaspBee/Conbee properly. Sets the level of the deCONZ command-line flag -dbg-error (default 0).Д«y default, deCONZ searches for RaspBee at /dev/ttyAMA0 and Conbee at /dev/ttyUSB0 when using other USB devices (e.g. Sets the level of the deCONZ command-line flag -dbg-otau (default 0). Sets the level of the deCONZ command-line flag -dbg-zdp (default 0). Sets the level of the deCONZ command-line flag -dbg-zcl (default 0). Sets the level of the deCONZ command-line flag -dbg-aps (default 0). Sets the level of the deCONZ command-line flag -dbg-info (default 1). ParameterД«y default, the web UIs ('Wireless Light Control' and 'Phoscon') and the REST API listen on port 80 only set this environment variable if you wish to change the listen port.Д«y default, the websockets service listens on port 443 only set this environment variable if you wish to change the listen port. Use these environment variables to change the default behaviour of the container. This image uses a manifest list for multiarch support specifying marthoc/deconz:latest or marthoc/deconz:stable will pull the correct version for your arch.

#Full uninstall 2.11 final serial serial

Pass the serial device at ttyUSB0 into the container for use by deCONZ (you may need to investigate which device name is assigned to your device depending on if you are also using other usb serial devices by default ConBee = /dev/ttyUSB0, Conbee II = /dev/ttyACM0, RaspBee = /dev/ttyAMA0 or /dev/ttyS0).

v /opt/deconz:/root/.local/share/dresden-elektronik/deCONZД«ind mount /opt/deconz (or the directory of your choice) into the container for persistent storage. on boot/reboot).Д®nsure the container has the correct local time (alternatively, use the TZ environment variable, see below). Start the container when Docker starts (i.e. If these ports conflict with other services on your host, you can change them through the environment variables DECONZ_WEB_PORT and DECONZ_WS_PORT described below. Uses host networking mode for proper uPNP functionality by default, the web UIs and REST API listen on port 80 and the websockets service listens on port 443. Marthoc/deconz Command line Options Parameter Running the deCONZ Container Pre-requisiteД«efore running the command that creates the deconz Docker container, you may need to add your Linux user to the dialout group, which allows the user access to serial devices (i.e.

Please consult Docker Hub for the latest available versions of this image. The 'latest', 'stable', and 'version' tags have multiarch support for amd64, armv7, and arm64, so specifying any of these tags will pull the correct version for your architecture. Test builds of this image, not for use by end users, only for developer testing! Specific versions of deCONZ, use only if you wish to pin your version of deCONZ RaspberryPi 2/3B/3B+, and other arm64 boards) architectures RaspBee is supported on armhf/ armv7 and aarch64/ arm64 (and see the 'Configuring Raspbian for RaspBee' section below for instructions to configure Raspbian to allow access to the RaspBee serial hardware).Д«uilds of this image are available on (and should be pulled from) Docker Hub, with the following tags: Tag This image runs deCONZ in 'minimal' mode, for control of the ZigBee network via the WebUIs ('Wireless Light Control' and 'Phoscon') and over the REST API and Websockets, and optionally runs a VNC server for viewing and interacting with the ZigBee mesh through the deCONZ UI.Д¬onbee is supported on amd64, armhf/ armv7, and aarch64/ arm64 (i.e.

#Full uninstall 2.11 final serial software

This Docker image containerizes the deCONZ software from Dresden Elektronik, which controls a ZigBee network using a Conbee USB or RaspBee GPIO serial interface.